Tevo Tarantula 3D Printer – Flashing new Model of Marlin Firmware with EasyConfig



On this video I talk about how one can flash your TEVO Tarantula 3D printer with the Marlin firmware.

►Arduino IDE: https://goo.gl/CqbRxA
►EasyConfig Marlin Fork: https://goo.gl/mJxJAP

I obtained this Tevo Tarantula from Gearbest.com freed from cost for assessment.

Get your equipment from gearbest.com ► https://goo.gl/CiBYny

Use coupon code “TevoTara” to get it for $189.99 or use code “GBTE” to get 12% off.

Acquiring and flashing:
Go to to the Marlin Tarantula gihub repo and choose “EasyConfig” from the department dropdown. On the best click on on “Clone or Obtain” and eventually on “Obtain ZIP”. Anticipate it to obtain, unpack it and go to the Marlin listing inside the basis listing you simply unpacked.

Navigate to the example_configurations listing and replica the contents of the “Tevo Tarantula” folder. Return to the Marlin root listing and paste the config information, overwriting those already there.

Open Marlin.ino with the Arduino IDE. Within the instruments menu below “Board” ensure you have “Arduino/Genuino Mega or Mega 2560” chosen. Test that processor is about to “ATMega2560”. Don’t forget to confirm the port you’re utilizing.

Change to the tab with the configuration.h file, that is the place all of the magic occurs, the place you may set the positions of the top switches, invert motors and set the PID’s for hotend and heatbed.

Lets check out the “EasyConfig” a part of the configuration:
In tools choices, SD help is outlined, additionally “y motor on proper” is outlined – since mine is on the left, I’ll remark that out. If in case you have a Tarantula with a big print mattress you’ll allow that right here.

I don’t want offsets, I additionally depart the step settings for now, since I can tune them through LCD module later.

If in case you have a Z probe, you’ll remark that in right here and likewise modify the sensor offsets correctly.

Mattress stage mode is about to guide, when you’ve got a Z probe you’ll modify that accordingly. “GRID_POINTS” is about to three which is able to measure at 9 totally different factors if you begin the mattress stage mode from the LCD module.

I wouldn’t have a second extruder, so I depart these settings alone. I additionally depart the PID’s as they’re, similar with the XTRA_BED back and front settings since they aren’t wanted on my 200x200mm print mattress.

OK, that’s it – hit the add button and as soon as the firmware is flashed the board will reboot and you’re good to go.

Prusa 3D Printer

Latest Comments

  1. Ong Wei Quan November 15, 2017
  2. Lucas Ault November 15, 2017
  3. Charles Graham November 15, 2017
  4. Jakub Polomsky November 15, 2017
  5. mikko November 15, 2017
  6. l3litz November 15, 2017
  7. Christian Röckl November 15, 2017
  8. william Howden November 15, 2017
  9. OfficialHaloFire November 15, 2017
  10. Ionut St. November 15, 2017
  11. So Gm November 15, 2017
  12. MadeByGamersForGamers November 15, 2017
  13. Patricio Freire November 15, 2017
  14. guillermo vt November 15, 2017
  15. D S November 15, 2017
  16. Darkmagister.org November 15, 2017
  17. Leo Carr November 15, 2017
  18. Guillermo Contreras November 15, 2017
  19. Noctaro Quad November 15, 2017
  20. Nevzat Güneşdoğdu November 15, 2017
  21. kuhdjaku November 15, 2017

Leave a Reply